How to use
Magic Classic 3D Printing Pen
Product appearance display
Operating steps
1. Plug the power adapter to the power jack,then the yellow LED light ,it It says it's already in service mode.
2. LCD screen display "PCL", usually choose 90 °C.
3. The red LED lights for preheating, when LED lights from red to green, preheating end equipment can work.
4. Material from the top of the feed hole insert, press the Forward Button.Pen spray glue, can start painting, Doubleclick can feed automatically (Use of consumables, port must be level).
5. Stepless speed change, according to the drawing speed to adjust the speed of the material.
6. Different colors have different melting points,please adjust according the temperature.
7. Long press the reverse button or double-click can be automatically refunded.
8. The equipment automatically enter standby state of sleep after 3minutes and 30 seconds, LCD screen display "SLEEP". If you need to use again to press the forwar Button
Do not touch the nozzle or any hot spots.
The way the filament head should be
If you want to change the color of same filament , renew the filament or change new one, but make sure the material port is smooth.
If a problem is encountered^heck in the following table,if you still can’t solve the problem,contact your seller or our customer service
Specification
Extrusion mode:Melting
Formation:3D
Drawing margin:None
Width of extrusion:Manual
Material used:PCL
Diameter of material:1.75mm
Speed of extrusion:adjustable
Nozzle hole size:0.7mm
Theological extrusion quantity: 0.076-0.86mA2
per minute.Adjustable
Melting temp of material: 70—100
Adapter current: 110V-240V~ 50/60HZ 0.65AMAX
Pen electric spec:DC5V 2A 10W
The DC head diameter: 3.5mm*1.35mm
Pen size:158mm*25mm*25mm
Weight: 0.05KG
Warning
1 .This equipment is suitable for the six years of age and older children and adults use. Children must be under adult supervision can use IFront near the tip and the device for high temperature danger zone, the highest temperature at about 40 t.Can’t use hand touch pen parts in use process.
2. Do not touch any hard objects with the nib
3. Do not block the feed inlet or nib with foreign body
4. Due to the difference between material physical properties and wire diameter of different manufacturer, do not use any materials from other company.
5. Please do not touch water. The equipment is precision electronic instrument.
6. Please place in the safety position to prevent from dropping or children playing.
7. Please make sure to separate the equipment from power adapter and materials after the use, in case of accidents to damage or destroy the equipment, such as lightning.
Magic Wireless Plus 3D Pen
Product appearance display
Operating steps
1. Long press the feed-in switch button for 3 seconds to starting up , The screen is displayed in sequence when the pen is started "Wincoud/Mode:PCL/electric quantity/AimT:80°C".
2. After the heating is done , double-click feed-in switch , insert the material into the feed hole and push forward to the automatic feed hole.
3. When you need to close the pen , double-click the exit button automatic exit material , After material exits completely , Long press the feed-in switch all the way to the light flicker to prove the shutdown worked.
4. When the material reaches the end of the pen, the remaining materials should be withdrawn from waste disposal.
5.The front of the pen must be aligned with the front of the base when charainq.
The way the filament head should be
If you want to change the color of same filament , renew the filament or change new one , but make sure the material port is smooth.
The tail is cut into a flat surface for next use.
Product function introduction
Display glass
Display current electricity and temperature when used.
Feed-in switch and Switch button
Click the pause, double click the feed, and switch for 3 seconds.
Returning switch
Click pause, double click back. Entry mode adjustment by 4 seconds:80°C/90°C
Heat dissipating hole
Exorbitant internal hot-melt temperature in avoidance of use.
Charging mouth
Plug the base into the charging hole to charge.
Injector
Upgrade to 1 pen, more smooth out of material
ipen charge indicator
Red light is always bright when charged , the red light will extinct when it full.
Base charge indication
Less power than left 1 lights flashing, full power 4 lights often light.
The base switch
Press the switch to know the rest power of the base.
Specification
Extrusion mode:Melting
Formation:3D
Drawing margin:None
Width of extrusion:Manual
Material used:PCL
Diameter of material: 1.75mm
Nozzle hole size:1.0mm
Melting temp of material: 70—100
ipen input voltage range parameter: DC4.8-5.2 V/1A
ipen input current parameter: less than 0.8A
ipen outside contour size:176mm*26mm*26mm
ipen the net weight:0.062KG
Pedestalinput electrical parameters: DC 5V/2A
USB interface type: MicroUSB interface
Outside dimension of pedestal: 100mm*90mm*60mm
Net weight of pedestal: 0.19KG
Trouble removal/Maintenance
If a problem is encountered,check in the following table,if you still can’t solve the problem,contact your seller or our customer service.
Warning
1. This equipment is suitable for the six years of age and older children and adults use. Children must be under adult supervision can use IFront near the tip and the device for high temperature danger zone, the highest temperature at about 40°C .Can't use hand touch pen parts in use process.
2. Do not touch any hard objects with the nib
3. Do not block the feed inlet or nib with foreign body
4. Due to the difference between material physical properties and wire diameter of different manufacturer, do not use any materials from other company.
5. Please do not touch water. The equipment is precision electronic instrument.
6. Please place in the safety position to prevent from dropping or children playing.
7. Please make sure to separate the equipment from power adapter and materials after the use, in case of accidents to damage or destroy the equipment, such as lightning.